INTEX® OWNER’S MANUAL Built-in Fast-Fill™ Electric PumpModel AP619A Manual

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/28/2015

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/28/2015

INFLATION

1. Move the product to the power source location.

Open line cord compartment cover. See Fig (1).

2. Plug in the AC line cord into an AC electrical outlet. See Fig

(2).

3. Turn the control dial clockwise until arrow points to the inflation mark ( ). See Fig

(3).

4. Press “I” to switch ON. See Fig

(4).

5. When the airbed is fully inflated to the desired firmness, press “O” to switch OFF. See Fig

(5).

151 151

IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

INTEX

OWNER’S MANUAL

Built-in Fast-Fill™ Electric Pump

Model AP619A 110 – 120 V~ 60 Hz 0.9 A

151-***-R1-1608

To reduce the risk of burns, fire, electric shock, or injury to persons:

• Infantshavesuffocatedoninflatablemattresses.Neverplaceinfantagedbirthto15monthstosleeponthis

inflatable air mattress / air bed. Infants can suffocate on an underinflated or deflated mattress, on bedding ,

by co-sleeping with another person, and by entrapment between the mattress and bed frame or between the

mattress and a vertical surface.

• Childrencanbeentrappedbetweentheinflatablemattressandanadjacentverticalsurface.Provideatleasta

shoulder width space between the inflatable mattress/airbed and adjacent vertical surfaces such as walls,

dressers or other objects.

• Alwayskeeptheinflatablemattressfullyinflatedwheninuse.

• Never introduce any flammable substance into the inflatable airbed,

SUCH AS AEROSOL TIRE REPAIR

PRODUCTS, as it may ignite or explode.

•

For indoor household use only.

• Unplug from outlet before putting on or taking off parts.

• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disable persons.

•

Use this furnishing only for its intended use as described in these instructions. Do not use attachments

not recommende d by the manufacturer.

• Do not operate where aerosol (spray) products are being used or where oxygen is being administered.

•

This is not a toy. Children must not be left unattended when using the airbed.

•

Keep the storage bag away from babies and children. The storage bag is not a toy. When not in use,

fold the bag and put it away out of the reach of children.

•

Do not walk, stand on or jump on or use the airbed as a trampoline.

•

Do not use on or near water. This is not a raft.

•

Do not set up bed near stairs, doors, sharp edges or breakable objects. Provide adequate space

between bed and objects to avoid entrapment.

•

Make sure the area is flat, smooth, free of sharp objects that could puncture the bed and keep away

from ledges.

•

Keep pets away from the airbed. Pets may puncture the surface of the bed.

•

Avoid sleeping on the edge of the airbed. Edges produce less support than the middle of the bed.

•

Do not operate air pump for more than 5 minutes at a time. Let pump cool at least 15 minutes between use.

•

Unplug electrical power cord when not in use. To disconnect, turn all controls to the off position, then remove

plug from outlet.

•

Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and

the like. Never drop or insert object into any opening.

• Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been

dropped or damaged, or dropped into water. Return the furnishing to a service center for examination and/or

repair.

•

If the AC supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to

avoid a hazard.

•

Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route

cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.

Keep the cord away from heated surfaces.

FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID SUFFOCATION, PROPERTY DAMAGE,

ELECTRIC SHOCK, BURNS OR OTHER INJURY.

WARNING

PARTS REFERENCE

Part Descriptions:

1. AC line cord

2. Switch

3. Inflation mark ( )

4. Deflation mark ( )

5. Air passage & control

dial valve

6. Control dial

7. Cord compartment cover

8. Airbed

FIG (1) FIG (2)

√

110 – 120 V

220 – 240 V

NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale. Due to a

policy of continuous product improvement, Intex reserves the right to change specifications and

appearance, which may result in updates to the instruction manual, without notice.

•

To reduce the risk of electric shock or injury, use indoors only, do not expose to rain. Store indoors.

CAUTION

•

To reduce the risk of electric shock: Always unplug this furnishing from the electrical outlet before cleaning.

DANGER

OPERATING INSTRUCTIONS

General

•

This appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized

outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit,

contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

Maintenance instructions:

•

No air pump maintenance is required. Air pump has no user serviceable parts.

• For cleaning use only mild soapy solution. Do not use any chemicals.

• In case of repairs, use only common PVC repair glue and patches.

SERVICING OF A DOUBLE-INSULATED PRODUCT:

In a double-insulated product, two systems of insulation are provided instead of grounding. No

grounding means is provided on a double-insulated product, nor should a means for grounding be

added to the product. Servicing of a double-insulated product requires extreme care and knowledge

of the system, and should be done only by qualified service personnel. Replacement parts for a

double-insulated product must be identical to those parts in the product. A double-insulated product

is marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED” and with the symbol .

READ AND SAVE THESE INSTRUCTIONS

Page 1

READ AND SAVE THESE INSTRUCTIONS

Page 2

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/28/2015

151

(151) AP619A BUILT-IN ELECTRIC PUMP ENGLISH 4.875” X 7.25” 07/28/2015

151 151

6. Lie down on the airbed to test the firmness.

7. If the sleeping surface is too hard, adjust the firmness

by turning the control dial counterclockwise gradually

until air starts to exit through the air passage. See

Fig

(6)

. Turn the control dial fully clockwise when the

desired firmness is achieved. See Fig

(7)

. If the airbed

becomes too soft repeat step #3 thru #7 as necessary.

8. Disconnect the AC line cord from the wall socket,

place it inside the cord compartment and close the

cover. Make sure the power cords are free of twist,

kink and knot.

FIG (6)

FIG (7)

Proper inflation of the airbed.

The ambient temperatures of air have an effect on the airbed internal pressure. At low

ambient temperature the air will contract within the airbed and the airbed will feel softer:

add air as necessary. At high ambient temperature the air within the airbed will expand

significantly and the airbed will become hard and may burst: release air to avoid damage

to the airbed or to soften the feel. Do not expose the airbed to extreme temperatures (hot

or cold).

Stretching is a natural characteristic of new vinyl. During initial use, the airbed may become

soft and require additional inflation to maintain desired firmness. This is normal for the first

few days of use.

Dimensions shown are approximate and will vary due to the vinyl temperature and the air

temperature.

In no event shall Intex, their authorized agents or employees be liable for damages

(such as pin holes) to the airbed caused by negligence, ordinary wear and tear,

abuse and carelessness, or external forces.

IMPORTANT NOTE

DEFLATION

1. Open line cord compartment cover. See Fig

(1).

2. Plug in the AC line cord into an AC electrical outlet. See Fig

(2).

3. Turn the control dial counterclockwise until arrow points to deflation mark ( ). See

Fig

(8).

Marketi

,CA 90801-14

USA

countr

ies of the wor

ld by In

rading Ltd.,u

nder l

icen

se from In

Trademarks

sed in some

004 In

Recreatio

p.,

Made in Ch

na/F

brique

Chine/Hec

o en China

FIG (8)

FIG (9)

Marketi

,CA 90801-14

USA

countr

ies of the wor

ld by In

rading Ltd.,u

nder l

icen

se from In

Trademarks

sed in some

004 In

Recreatio

p.,

ade in Ch

na/F

brique

Chine/Hec

o en China

FIG (10)

INFLATION OPTION

1. If electrical power is not available then a conventional foot

or manually operated air pump can be connected to the

control dial valve for inflation. See Fig

(11).

2. Turn the control dial clockwise until arrow points to the

inflation mark ( ).

3. Insert air pump nozzle to the control dial valve to inflate the

airbed.

FIG (11)

Inflate only with a low pressure inflator. Do not over inflate. Fill with cold air only.

IMPORTANT

STORAGE INSTRUCTIONS

1. Deflate the airbed following the “DEFLATION” instructions.

2. Turn the control dial counterclockwise until arrow points to deflation mark ( ). See

Fig

(8).

3. Make sure the airbed is clean and dry.

4. Lay bed flat with sleeping surface facing upwards and follow the folding steps on Figs

(12 – 16)

. Fold the airbed loosely and avoid sharp bends, corners and creases which can

damage the airbed.

FIG (12)

FIG (13)

FIG (14)

INTEX

FIG (16)

INTEX

FIG (15)

INTEX

5. Turn the control dial fully clockwise. See Fig (10).

6. Place the airbed inside the storage bag and store in a dry, cool storage location.

en China/Gedruckt in China.

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas

utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/

a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA

90801

•DistributedintheEuropeanUnionby/Distribuédansl’UnionEuropéennepar/DistribuidoenlauniónEuropeapor/VertriebinderEuropäischen

Union durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands Consumer Service 1-800-234-6839

www.intexcorp.com

4. Press “I” to switch ON. See Fig

(4).

5. When the airbed is completely deflated, begin rolling the airbed from the foot of

the airbed towards the head of the airbed where the pump is located. See Fig

(9).

6. When all air is removed from the airbed, press “O” to switch OFF. See Fig

(5).

7. Turn the control dial fully clockwise. See Fig

(10).

8. Disconnect the AC line cord from the wall socket, place it inside the cord compart

ment and close the cover. Make sure the power cords are free of twist, kink and

knot.

FIG (5)FIG (4)

FIG (3)

Marketing Ltd.

Long Beach,CA 90801-1440 USA

countries of the world by Intex

Trading Ltd.,under license from Intex

Trademarks used in some

200

4 Intex Recreation Corp.,

ade in China/Fabrique en Chine/Hecho

en China

READ AND SAVE THESE INSTRUCTIONS

Page 3

READ AND SAVE THESE INSTRUCTIONS

Page 4

Leave a Comment Cancel reply