Bissell Proheat 2x Revolution Pet pro User Guide

PROHEAT 2X

REVOLUTION

™

PET PRO

_______________

USER GUIDE

2066 SERIES

www.BISSELL.com

READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.

When using an electrical appliance, basic precautions should be observed, including the following:

IMPORTANT SAFETY INSTRUCTIONS

» Unplug from electrical socket when not in use

and before cleaning, maintaining or servicing the

appliance.

» This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack

of experience and knowledge if they have been

given supervision or instruction concerning use of

the appliance in a safe way and understand the

hazards involved. Cleaning and user maintenance

shall not be made by children without supervision.

» Children should be supervised to ensure that

they do not play with the appliance.

» If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a

hazard.

» Do not run appliance over cord.

» Keep hair, loose clothing, fingers, and all parts of

body away from openings and moving parts of

the appliance and its accessories.

» Use only the type and amount of liquids specified

under the Operations section of this guide.

» Do not leave appliance when plugged in.

» Always connect to a properly earthed electrical socket. Do not modify

earthed plug.

» Do not allow to be used as a toy.

» Use only as described in the user guide.

» Use only manufacturer’s recommended attachments.

» Do not use with damaged cord or plug.

» Do not immerse in water or liquid. Use only on surfaces moistened by the

cleaning process.

» If appliance is not working as it should, has been dropped, damaged, left

outdoors, or dropped into water; do not attempt to operate it and have it

repaired at an authorized service center.

» Liquid must not be directed towards equipment containing electrical

components.

» Do not pull or carry by cord, use cord as a handle, close door on cord, or

pull cord around sharp edges or corners.

» Keep cord away from heated surfaces.

» Do not unplug by pulling on cord.

» To unplug, grasp the plug, not the cord.

» Do not handle plug or appliance with wet hands.

» Do not put any object into openings.

» Do not use with any opening blocked; keep free of dust, lint, hair, and

anything that may reduce air flow.

» Turn off all controls before unplugging.

» Use extra care when cleaning on stairs.

» Do not use to pick up flammable or combustible liquids, such as petrol, or

use in areas where they may be present.

» Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.)

» Do not use appliance in an enclosed space filled with vapors given off by

oil base paint, some mothproofing substances, flammable dust, or other

explosive or toxic vapors.

» Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.

» Keep appliance on a level surface.

» Do not carry appliance while in use.

» Unplug before attaching the TurboBrush™ tool.

» Do not pick up anything that is burning or smoking, such as cigarettes,

matches, or hot ashes.

» If your appliance is fitted with a nonrewireable BS 1363 plug it must not

be used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in the

carrier contained in the plug. Spares may be obtained from your BISSELL

supplier. If for any reason the plug is cut off, it must be disposed of, as it is

an electric shock hazard should it be inserted into a mains socket.

» Do not expose to rain. Store indoors.

» Always install float before any wet pick-up operation.

» Plastic film can be dangerous. To avoid danger of suffocation, keep away

from children.

» Have servicing performed by a qualified repair person using only identical

replacement parts. This will ensure that the safety of the product is

maintained.

SAVE THESE INSTRUCTIONS

FOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.

This model is for household use only.

WARNING

To reduce the risk of ﬁre, electric

shock, or injury:

Caution.

Refer to instruction manual.

This symbol means to recycle.

Recycling to help the environment. Dispose of packaging at the applicable recycling collection point. This symbol means to

recycle. Do not mix packaging with general household waste.

This symbol on the product and/or accompanying documents means that used electrical and electronic products should not

be mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designated

collection points. Please contact your local authority for further details of your nearest designated collection point.

www.BISSELL.com

Assembly

A Phillips screwdriver is

required for Assembly in

Step 3.

3 4

Next, align the carry handle with the slots

on either side of the base (behind the

power switch and cleaning mode switch).

The carry handle will “click” into place.

First, insert the

(aluminum)

Upper Handle

at the top of the

base until you

hear a “click”.

Do NOT put

the clean tank

on the machine

until Step 5.

Use a Philips screwdriver

to secure the screw (found

taped to upper handle)

into the carry handle.

Wrap the cord around

the carry handle and Quick

Release™ Cord Wrap hook.

At the bottom of the

upper handle, align the

clean water tank with

the grooves and slide

the tank into place.

WARNING

Do not plug in your deep cleaner until you are familiar with all instructions

and operating procedures.

Your deep cleaner

comes in four

easy-to-assemble

components and

an accessory bag.

• Base

• Upper Handle

• Clean Water Tank

• Carry Handle

click

Side

View

Quick Start Guide

www.BISSELL.com

Safety Instructions…………..2

Quick Start Guide……………3

Product View……………….5

Cleaning Formulas…………..6

Operations ……………….7-9

Hose, Tools & CleanShot® ….10-12

Maintenance & Care ………13-17

Troubleshooting …………….18

Guarantee …………………20

Service ……………………20

NOTE: Standard accessories

may vary by model. To identify

what should be included with

your purchase, please refer

to the “Carton Contents” list

located on the carton top flap.

Package Contents

Thanks for buying a BISSELL carpet cleaner!

We love to clean and we’re excited to share one of our innovative products

with you. We want to make sure your carpet cleaner works as well as it

does today for years to come, so this guide has tips on using (pages 7-12),

maintaining (pages 13-17), and if there’s a problem, troubleshooting (page 18).

In just a few simple assembly steps, you’ll be ready to deep clean. Flip to the

Quick Start Guide on page 3 and let’s get started!

1. 2. 3. 4.

5. 6.

10.

1. Upper Handle

2. 1 Screw attached to

Upper Handle

3. Base with Dirty Water Tank

4. Clean Water Tank

5. Carry Handle

6. Trial Size BISSELL Formulas (3)

7. Accessory bag & hose

8. Tough Stain Tool

9. 2-in-1 Pet Upholstery Tool

10. Nozzle Clean Out Tool

www.BISSELL.com

Getting to Know Your Deep Cleaner

Upper

Handle

In-Use

Cord Clip

Cleaning Mode

Switch

CleanShot®

Button

EdgeSweep®

Brushes

Carry

Handle

Rubber

Tab

Quick

Release™

Cord Wrap

Recline

Pedal

Formula Cap

Clean Water Tank

(3.7 Liter Capacity)

Power

Button

Float

Stack

Dirty Water Tank

Belt Access

Foot

Spray Trigger

Belt/Brush

Access Plate

Nozzle

Belt

Access Door

www.BISSELL.com

WASH & PROTECT

WASH &

REMOVE

WASH & REFRESH

WASH &

SHINE

Professional

Stain & Odour

Pet Stain &

Odour

Stain & Odour + Oxy

Febreze™

Blossom &

Breeze

Febreze™

Cotton Fresh

Natural

Orange

Hard Floor

Cleaner

Professional

strength to

remove extra

tough stains

and odours

Includes

Scotchgard™

Protector

Removes tough

pet stains

and contains

patented

odour removal

technology

Includes

Scotchgard™

Protector

Removes

tough stains

and odours

Includes

Scotchgard™

Protector

Permanently

removes

tough stains

like red wine,

coffee, tea,

cola and grape

juice with

Active Oxygen

Technology

Powerful

cleaning

with a

refreshing

spring scent

Powerful

cleaning

with a

refreshing

clean scen

Powerful

cleaning

with a

refreshing

natural

orange

scent

Removes dirt

and grime

from sealed

hard floor

surfaces;

leaves a

natural shine

PRETREAT

PRE TREAT SPOTS AND STAINS

TO IMPROVE CARPET CLEANING

PERFORMANCE

Stain PreTreat Pet Stain PreTreat

Pretreat to

penetrate

and loosen

tough stains

Pretreat to help

remove tough

pet stains

and odors

Keep plenty of genuine BISSELL formula

on hand so you can clean whenever it fits

your schedule.

Always use genuine BISSELL deep

cleaning formulas. Non-BISSELL cleaning

formulas may harm the machine and may

void the guarantee.

Cleaning Formulas

WARNING

To reduce the risk of ﬁre and electric shock due to internal component damage, use only

BISSELL cleaning ﬂuids intended for use with the deep cleaner.

ONLY BISSELL Wash & Protect formulas protect from future stains with Scotchgard™ Protector.

Scotchgard™ is a trademark of 3M®.

*60 mL of 2X concentrated formula is equivalent to 120 mL of non-concentrated formula.

Tips Before Carpet Cleaning

• If cleaning an entire room, consider moving your furniture to another area.

• Remove loose dirt and impediments.

• Pre-treat stains with BISSELL PreTreat to improve performance on tough

stains and ground-in dirt.

2X* CONCENTRATED CLEANING FORMULAS

www.BISSELL.com

Always use genuine BISSELL deep cleaning formulas. Non-BISSELL

cleaning solutions may harm the machine and may void the guarantee.

NOTE: Fill with hot (140°F/60°C MAX) tap water and add the appropriate

BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR

TANK IN MICROWAVE. Do not substitute BISSELL Cleaning Formula with other

household cleaning products.

Unscrew the cap from the clean water tank. Add hot

tap water to the water fill line. Next, reference the chart

below for formula amounts to add to the tank. Twist

cap back into place.

Lift the clean water tank

straight up to remove from

the machine.

The clean water tank is at the

top of the machine.

Clean Water Tank

(3.7 Litre)

Dirty Water Tank

At the bottom of the upper

handle, align the clean water

tank with the grooves and

slide the tank into place.

FORMULA FILLING

INSTRUCTIONS

DEEP CLEAN MODE EXPRESS CLEAN MODE

BISSELL 2X

Concentrated Formulas

Fill water to the Water

Fill Line, then add 74 mL

of formula.

Fill water to the Water

Fill Line, then add 37 mL

of formula.

Filling Your Clean Water Tank:

2X Concentrated Formula

NOTICE: Do not over wet carpet. Be careful not to run over loose objects or

edges of area rugs. Stalling the brush may result in premature belt failure.

www.BISSELL.com

Cleaning Your Carpet

Press the power button

to turn the machine on.

To recline your machine

for use, press the recline

pedal with your foot.

Plug into a properly

earthed outlet.

Select

cleaning

mode:

Deep Clean

Delivers a deep

clean to your

carpet.

Express Clean

Provides a lighter

clean with about

1 hour of dry time.

Deep Clean Mode:

1. Press the spray trigger to apply solu–

tion while making 2 slow wet passes – 1

forward and 1 back.

2. Release the trigger.

3. Make 2 slow dry passes – 1 forward

and 1 back, to suck up the dirty solu–

tion. (Do not hold down the trigger for

this step.)

NOTE: For best cleaning performance,

clean with your machine in Deep Clean

Mode.

Express Clean Mode:

1. Press the spray trigger to apply solu–

tion while making 2 wet passes – 1 for–

ward and 1 back.

2. Release the trigger.

3. Make 2 dry passes – 1 forward, 1 back

to suck up the dirty solution. (Do not

hold down the trigger for this step.)

NOTE: In Express Clean Mode, the

dirty tank will not get as full as when

cleaning with Deep Clean Mode.

NOTICE: To prevent damage to Berber carpets, avoid repeated strokes in

the same area.

www.BISSELL.com

Bare Floor Cleaning

With the machine unplugged,

attach the bare floor tool to

the bottom of the machine

by lining the tool to the edge

of the nozzle. Rotate down

until it clicks into place.

Follow filling instructions

on page 10 or 11 and switch

cleaning mode to Express

Clean.

When finished, unplug the

machine and remove the

bare floor tool by rotating

the tool up to unhook

from the nozzle.

Rinse and let dry before

storing. Refer to page 13

for emptying the dirty

water tank. Refer to

page 14 for cleaning your

machine before storing.

Plug into a properly

grounded outlet and press

the power button.

Clean by pressing the

trigger for 1 wet pass

forward, 1 wet pass back,

and then release the

trigger and make 1 dry pass

forward, 1 dry pass back.

WARNING

WARNING: To reduce the risk of ﬁre and electric shock when cleaning a hard ﬂoor, the

BISSELL bare ﬂoor tool must be used and is only to be used with BISSELL Wash & Shine

Hard Floor Cleaner formula intended for use with this appliance.

NOTE: The bare ﬂoor tool that is compatible with the ProHeat 2X Revolution

may not be included. It is available for purchase by contacting our team by

phone or visting us online at BISSELL.com.

*Select models only

Important! Please check manufacturer’s tag before cleaning area rugs for

any specialized cleaning instructions. We do not recommend deep cleaning

delicate, silk, wool, antique or area rugs without a manufacturer’s tag.

Area Rug Cleaning

• Check the manufacturer’s tag.

• Select Express Clean Mode.

• When cleaning area rugs, place the rug on a sealed surface to test for colorfastness

in an inconspicuous area. Your cleaner should not be used on unsealed surfaces.

• Important: Keep the foot of the deep cleaner perpendicular to the rug’s edge with

each cleaning pass to prevent damage.

Regularly clean your high-traffic area rugs in Express Clean Mode:

www.BISSELL.com

Cleaning with Hose & Tool

Insert the hose and

snap into place.

Be sure the colored

hose release clip

is facing out, away

from machine.

Press the spray trigger button to spray

the soiled area, then slowly move tool back

and forth over the area.

Release the trigger to suck up the dirty

solution. Work in small sections until the area

is clean.

When finished cleaning, turn the machine on

to suction up warm clean water to rinse the

inside of the hose and tool. Detach the hose

and tool and close the accessory hose door.

Let the hose and tool air dry before storing.

Attach the tool to the end of the hose.

(Tools may vary by model.) Press the

power button to turn machine on.

NOTE: If using the Deep Reach Tool (select models only) or Pet Stain Tool

(select models only) be sure the needles of the tool are pressed down into the

carpet so the spray gets into the carpet ﬁbers.

— Keep hair, loose clothing, fingers, and all parts

of body away from openings and moving parts.

Brushroll continues to rotate when in the upright

position.

— Brushroll continues to turn while product is

turned on and handle is in upright position. To avoid

damage to carpet, rugs, furniture and flooring, avoid

tipping cleaner or setting it on furniture, fringed

area rugs, or carpeted stairs during tool use.

— The brushroll remains on while cleaning with the

hose and tool. Do not allow cleaner to sit in one

location for an extended period of time, as damage

to floor can result.

Lift the accessory

hose door on top

of foot on the front

of the machine. The

door flips toward the

machine to open.

www.BISSELL.com

Cleaning with CleanShot®

Press the CleanShot® button with your foot.

The window of the button will be green and

show an “I” symbol when it is on.

Spray will continue until you turn it

off. To turn CleanShot® off, press the

button with your foot. The window of

the button will be red and show an “O”

symbol when it is off.

Completely cover the stain with CleanShot® spray. Allow the stain to soak. To

extract, maneuver the foot of the machine over the stain to brush and remove.

www.BISSELL.com

DRY MODE NOTE: Use a “raking” motion to clean. Start with the tool farthest

away and rake in small increments as you bring the tool toward you. The rubber

nubs will help attract hair to the suction channel.

Attach the tool and select dry mode

to first pick up dry debris and pet

hair. The suction will be at the lower

part of the tool, near the dry cup.

Follow hose plug-in instructions from

steps 1 & 2 on page 14.

NEW! 2-in-1 Pet Upholstery Tool

*Make sure your clean tank has water & formula to use the tool in wet mode..

Turn off the machine.

Hold the cup and twist

counterclockwise. Line up

the arrow with the unlock

symbol and remove.

Take off the cup

to empty hair

and debris.

To reattach the cup, line

up the cup to the tool

indents, and rotate clock

wise. The arrow will line

up with the locked icon

when secured.

To Deep Clean, move the

switch to wet mode. Press

the trigger to spray your

water and formula; use

the top of the nozzle to

extract stains and odors.

To remove any hair or

trapped debris from the

nozzle, first turn off the

machine. Pull the nozzle

tab away from the tool to

remove and rinse under

running water.

Replace the tool by lining

up the nozzle edge and

snap into place. Before

storing, make sure all hair

is removed from the dry

cup and nozzle has been

rinsed under running

water.

Dry Mode

(switch up)

Wet Mode

(switch

down)

Empty the cup when

it fills with hair and

debris.

Dry

Suction

Channel

Remove hair

that may wrap

around the filter.

Wet

Suction

Channel

WET MODE NOTE: Start from the area farthest away. Hold the trigger down, and

pull the tool toward you. Keep the tool in contact with the surface as you pull. You

will see extraction through the nozzle.

www.BISSELL.com

Empty Dirty Water Tank

To release dirty water

tank, press down on the

colored tank handle.

Tilt the tank slightly

toward you.

Grab the handle and tank

with both hands and pull

the dirty water tank up

and away to remove.

Clean the red filter

below the dirty

tank by wiping off

any remaining dirt

or debris.

For quick empty:

Pull the rubber tab

and tilt to pour.

(Located at the corner

of the top of the tank.)

When closing the

rubber tab, make

sure all edges are

sealed tight.

For final clean and

rinse: Unscrew the ring

at the bottom of tank.

Gently remove the

float stack, rinse,

and clean.

Once clean, return float

stack into the tank by

lining up the arrows

so they point at each

other. This is the only

way the float stack will

fit into the tank.

With the arrows

aligned, the float stack

should lock into place.

Return the ring and

twist to lock. Water

may leak if the ring is

not fully tightened.

Did You Know?

The Float Stack

is what prevents

your dirty

tank from

overﬂowing.

WARNING

To reduce the risk of ﬁre, electric shock or injury, turn power OFF and disconnect plug from

electrical outlet before performing maintenance or troubleshooting.

To return the dirty

tank: Angle the tank

and insert bottom

first. Then tilt the

tank toward the

machine and push

the top in until it

clicks into place.

www.BISSELL.com

Cleaning Machine After Use

To flush and rinse the

machine: Turn the machine

on and press the trigger for

15 seconds while making

back and forth passes on a

section of carpet.

Finally, release the trigger

and extract the water.

See page 13 to clean the

dirty tank from the water

that was just extracted.

Empty the clean water tank

and let dry before storing.

Wipe your machine’s

exterior with a soft cloth.

Store machine in a

protected dry area.

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from

electrical outlet before performing maintenance or troubleshooting checks.

First, fill the clean water

tank with warm tap water

and then empty it all to

rinse. Then fill again with

warm tap water and return

the tank to the machine.

Twist cap back on tightly.

NOTICE: To reduce the risk of a leaking condition, do not store unit where

freezing may occur. Damage to internal components may result.

www.BISSELL.com

Brush Roll & Nozzle Care

Turn off and unplug

the machine from the

grounded outlet.

Remove the nozzle

from the foot:

scoop and grip the

Accessory Hose

Door. Pull up to

remove the nozzle.

At this point, the

nozzle and brush

roll cover can

be rinsed under

running water and

the nozzle clean

out tool can be

inserted to unclog

hair or debris.

To reveal the

brush rolls.

Press on the

two release

buttons and lift

straight up.

NOTE: Be sure to clean the brush rolls and nozzle before storing your machine.

Follow these steps if your nozzle becomes clogged with hair or debris.

When finished, return the brush roll

cover by pushing it straight down.

You will hear a click from each “push”

button when the cover is pushed down

into place. Ensure the nozzle wire on

the front of the brush roll cover has

also snapped back into place. Line up

the nozzle from the edge near the floor

and rotate to snap back into place.

Use the comb

to brush out the

debris or hair from

the brush rolls.

click

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from

electrical outlet before performing maintenance or troubleshooting checks.

Pull forward the

nozzle wire on

the front of the

brush roll cover

for release.

www.BISSELL.com

Replacing Belts & Brush Rolls

What you will need: 1 Phillips screwdriver & 1 ﬂathead screwdriver

Use a flathead

screwdriver and

press it into

the Belt Access

Door slot. Lift to

remove the Belt

Access Door.

While the machine is upright, unplug the machine and remove both tanks. Remove

the nozzle and brush chamber cover (see steps in Brush Roll & Nozzle Care). Press

the recline pedal and lay the machine on its back.

With the machine

still on its back,

use a Phillips-head

screwdriver to

remove the screw

on the brushroll

end cap.

If the Gear Belt

is broken, gently

remove it. If you

are replacing your

brush rolls, gently

remove the belt.

There are washers

at the ends of the

brush rolls, be

careful that these

do not fall off or

get lost.

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from

electrical outlet before performing maintenance or troubleshooting checks.

With the machine laying on its back,

locate the belt access plate. Use a

Phillips-head screwdriver to remove the

belt access plate screw.

Remove the Belt Access Plate.

www.BISSELL.com

Turn the machine

on its side and use a

Philips screwdriver to

remove the screw just

underneath the wheel.

Slide the wheel down

to remove.

Keep it wrapped

on the red pulley

and adjust the

machine so it is

laying on it’s back

again. Use your

thumb to stretch

the flat belt back

to wrap around

the metal axle.

If the flat belt is broken,

gently remove the belt.

If it needs replacing for

any reason, the gear

belt should already

be removed before

removing the flat belt.

Rotate the machine

back to its side. Feed

the new flat belt

through the opening

so that it wraps around

the red pulley.

Replacing Belts & Brush Rolls (Continued)

NOTE: To replace

brush rolls, remove

them from the

metal posts and

replace. Make sure

the metal post

goes completely

through the end of

the brush roll. The

brush roll bristles

should be aligned

in a ‘V’ pattern as

pictured.

Align brush rolls with belt at other

end. To ensure alignment, hold the

end of one brush roll and twist.

The other brush roll rotates with it.

Check that washers are in place.

Reassemble the belt and end cap,

securing with screws you removed.

Snap the Belt Access Door back

down into place.

Resecure the Belt/Brush Access Plate:

Slide the wheel up back into the slot and

secure with the screw that was removed.

NOTE: See Step 7 on page 15 for how to put the brush roll cover and nozzle back

in place.

www.BISSELL.com

Problem Possible causes Remedies

Reduced or No

Spray Through

Foot of Machine

Clean water tank may be empty

Refill tank

Clean water tank may not be

seated completely

Turn power OFF; remove and reseat tank

No spray

through

hose & tool

The hose to your machine is not primed or

may have lost prime

1. With the machine off and unplugged, remove the nozzle from

the foot. Place a ball point pen in the black cylinder next to the

screw. When water bubbles up, remove the pen. Reassemble the

nozzle and hose

2. Hold end of hose below water level in tank to prime

3. With the clean tank full of water, the machine OFF and

RECLINED, press the CleanShot® button ON and wait for the

CleanShot® to drain for a few seconds; This will re-prime the

machine

Clean Water tank may be empty Refill the Clean Water Tank

Clean Tank may not be seated properly Turn power OFF; Remove and reseat the clean water tank

No Spray

Through

CleanShot®

Clean Water tank may be empty Refill the Clean Water Tank

Clean Tank may not be seated properly Turn power OFF; Remove and reseat the clean water tank

The machine is not reclined Press the Recline pedal and bring the handle down to recline the

machine

Pump may have lost prime With the machine off and unplugged, remove the nozzle from the

foot. Place a ball point pen in the black cylinder next to the screw;

When water bubbles up, remove the pen; Reassemble the nozzle

before cleaning again

CleanShot®

Continues Spray

When Machine

is Off

CleanShot® button is not in the “OFF”

position

Press the CleanShot® button to turn it off. The button window will

show the color red and a “O” symbol when it is in the off position

Loss of

suction

power

Dirty tank may not be seated properly Pick up the dirty tank and reseat so it fits in the unit

Dirty tank has picked up maximum amount

of dirty water and has reached full line

Empty dirty tank

Rubber tab on dirty water tank is not sealed

tight

Check the rubber tab on the dirty water tank and press firmly on all

edges to secure it tightly (see step 4 on page 15 for detail)

Accessory hose door may not be closed

tightly in place

Check the accessory hose door and make sure it is closed tightly – it

should be locked into place

Nozzle may be clogged from pet hair or

debris

Use the nozzle clean out tool and follow steps on page 15 for

“Cleaning Nozzle”

Brush roll cover not fully snapped into place Remove the nozzle and brush roll cover; Follow step 7 from page 15

and make sure you hear both buttons click into place

No power

Cleaning mode switch mistaken for power

button

Press the red power button on the left side of the machine to turn

the machine on

Outlet may not be active Try plugging in a different device that uses a grounded outlet to test

for power from the outlet

Leaking tank

Tank may have been over-filled 1. Make sure your tank has the water and formula in it that you’ve

prepared

2. With the cap twisted ON tightly, hold your tank at an angle, over a

sink or drain, so any extra water can pour out of the space

3. Wipe the tank dry with a cloth

Water may be caught in space between the

tank and the tank’s handle

Troubleshooting

WARNING

To reduce the risk of electric shock, turn power switch o and disconnect plug from

electrical outlet before performing maintenance or troubleshooting checks.

www.BISSELL.com

Notes

Grand Rapids, Michigan

Part Number 161-2614 06/17 RevD

Visit our website at: www.BISSELL.com

Scotchgard is a trademark of 3M

Csumer Guare

This Guarantee only applies outside of the USA and Canada. It is

provided by BISSELL International Trading Company BV (“BISSELL”).

This Guarantee is provided by BISSELL. It gives you specific rights.

It is offered as an additional benefit to your rights under law. You

also have other rights under law which may vary from country

to country. You can find out about your legal rights and remedies

by contacting your local consumer advice service. Nothing in this

Guarantee will replace or lessen any of your legal rights or remedies.

If you need additional instruction regarding this Guarantee or have

questions regarding what it may cover, please contact BISSELL

Consumer Care or contact your local distributor.

This Guarantee is given to the original purchaser of the product from

new and is not transferable. You must be able to evidence the date

of purchase in order to claim under this Guarantee.

Limited 6 Year Guarantee

(from the date of purchase by

original purchaser)

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below,

BISSELL will repair or replace (with new or remanufactured

components or products), at BISSELL’s option, free of charge, any

defective or malfunctioning part or product.

BISSELL recommends that the original packaging and evidence

of the date of purchase be kept for the duration of the Guarantee

period in case the need arises within the period to claim on the

Guarantee. Keeping the original packaging will assist with any

necessary re-packaging and transportation but is not a condition of

the Guarantee.

If for your product is replaced by BISSELL under this Guarantee,

the new item will benefit from the remainder of the term of this

Guarantee (calculated from the date of the original purchase). The

period of this Guarantee shall not be extended whether or not

your product is repaired or replaced.

*EXCEPTIONS AND EXCLUSIONS FROM

THE TERMS OF THE GUARANTEE

This Guarantee applies to products used for personal domestic use and

not commercial or hire purposes. Consumable components such as

filters, belts and mop pads, which must be replaced or serviced by the

user from time to time, are not covered by this Guarantee.

This Guarantee does not apply to any defect arising from fair wear

and tear. Damage or malfunction caused by the user or any third

party whether as a result of accident, negligence, abuse, neglect, or

any other use not in accordance with the User Guide is not covered

by this Guarantee.

An unauthorised repair (or attempted repair) may void this Guarantee

whether or not damage has been caused by that repair/attempt.

Removing or tampering with the Product Rating Label on the

product or rendering it illegible will void this Guarantee.

SAVE AS SET OUT BELOW BISSELL AND ITS DISTRIBUTORS ARE NOT

LIABLE FOR ANY LOSS OR DAMAGE THAT IS NOT FORESEEABLE

OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY

NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT INCLUDING

WITHOUT LIMITATION LOSS OF PROFIT, LOSS OF BUSINESS, BUSINESS

INTERRUPTION, LOSS OF OPPORTUNITY, DISTRESS, INCONVENIENCE OR

DISAPPOINTMENT. SAVE AS SET OUT BELOW BISSELL’S LIABILITY WILL

NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

BISSELL DOES NOT EXCLUDE OR LIMIT IN ANY WAY ITS LIABILITY FOR

(A) DEATH OR PERSONAL INJURY CAUSED BY OUR NEGLIGENCE OR THE

NEGLIGENCE OF OUR EMPLOYEES, AGENTS OR SUBCONTRACTORS; (B)

FRAUD OR FRAUDULENT MISREPRESENTATION; (C) OR FOR ANY OTHER

MATTER WHICH CANNOT BE EXCLUDED OR LIMITED UNDER LAW.

Csumer Care

If your BISSELL product should

require service or to claim under our

limited guarantee, please contact us

as follows:

Website:

www.bisselldirect.co.uk

Email:

UKSupport@bissell.com

Telephone:

0344-888-6644

Write:

BISSELL Homecare (Overseas) Inc.

Ground Floor

226 Berwick Avenue

Slough, Berkshire, SL1 4QT

United Kingdom

Spares are available for purchase.

To purchase visit www.4bissell.co.uk

Visit the BISSELL website: www.bisselldirect.co.uk

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: _____________ Please record your Purchase Date: _____________

NOTE: Please keep your original sales receipt. It provides proof of the date

of purchase in the event of a Guarantee claim. See Guarantee for details.

Leave a Comment Cancel reply